6 meter Super Gain Yagi Antenna With 15 meter Boom 6m10DX15
10 elements on tapered boom from 20 mm to 60 mm size. Devoted for EME and DX hunting.
With this antennas you will hear extreme weak signals that nobody could hear with smaller antennas.
15 meter boom antenna with extreme suppression of all side lobes (super low noise design) will ensure “Who will be the boss”. You will “open” and “close” the Magic Band.
What 6m10DX15 mean?
6m – Magic band antenna
10 – Elements
DX – Intended for use in DX part of band 50-50.5MHz with excellent SWR
15 – 15m tapered boom with extreme strong construction.
Electrical Specifications for 6m10DX15 antenna
Frequency Range: 50 – 50.5 MHz
Free Space Forward Gain: 14.7 dBi
Front to Back Ratio: 35 dB
Nominal Input Impedance: 50 Ohms
SWR Across Entire Band: < 1.2
Maximum Power Input: 1500 W
Matching Method: Direct 50 Ohms feed through common mode choke
Maximum Power Input options by order for 6m10DX15 Yagi antenna
“E” 7/16 DIN Input connector RG142 Teflon balun cable. Max power 2500 W (6m10DX15E)
“EX” 7/16 DIN Input connector RG115 Teflon balun cable. Max power 8000 W (6m10DX15EX)
Mechanical Specifications for 6m10DX15 Yagi
Number of Elements: 10
Element Diameter: Tapered elements. Center tube 12mm, extensions 10 and 8mm
Dipole Diameter: Tapered dipole. Center tube 12mm, extensions 10 and 8mm
Longest Element: 3.1 m
Element Mounting Position: Below the boom
Balun and Connectors: Included
Boom Length: 15 m
Boom Size: Tapered Boom 60×60 mm, 50×50 mm, 40×40 mm, 30×30 mm, 20×20 mm
Turning Radius: 9 m
Number of Boom Pieces: 10
Guy rope support: Yes, Included 4 ropes
Mounting Mast Diameter: 43 – 70 mm 1-11/16″ – 2-3/4″ OD
Clamp: M10 Stainless Steel
Survival Wind Speed: 120 km/h
Wind Load: 0.7 m2
Net Weight: 29 kg
Gross Weight: 32 kg
Transportation Length: 2 m
Dipole and 8000W balun view on 6m Magic Band antenna 6m10DX15EX. Connector forward.
Dipole and 1500W balun view on 6m Magic Band antenna 6m10DX15. Connector forward.
Antennas-Amplifiers Product Benefits
No tuning antennas
Before dispatch, we assemble each and every antenna and test antenna characteristics. That means you can expect exceptionally good electrical and mechanical characteristics including low SWR across the designed range immediately after assembling.
No need to move, cut, tune or use rasp for any element to get perfect SWR on intended frequency range. Everything is pre tuned.
That lead also to another very important detail. When assemble and test each antenna is complete with all washers, nuts, bolts guy rope supports etc.
When packing all parts are already on antenna without possibilities to “forget” important parts to put in the box. So you will always receive complete antenna what we tested just before dispatching.
Designs that work well in all weather conditions
Low SWR and superior G/T, F/B and F/S ratios across the entire band
Excellent mechanical properties
High durability, built without compromise
A Major advance in Amateur Radio antenna design.
All antennas have been calculated using state of the art full 3D Electromagnetic Simulation software including the influence of the boom, bracket, baluns and connectors.
The performance of antennas designed using these techniques are exceptional, far better than antennas designed using “wire” programs like EZNEC Pro/4 –NEC v5.0, 4NEC2, MMANA or AO
These programs cannot calculate the effect of any metallic or dielectric structures near the antenna elements and therefore must be considered inaccurate.
Designs are optimized using the Particle Swarm algorithm, which is considered one of the best antenna optimization algorithms available, followed by a classic Nelder-Mead Simplex algorithm for fine-tuning.
Ordered antennas are always complete
That means that you do not need to buy or add to order balun, connector or guy rope support.
Everything is included.
Designed to last.
Click here to look all 6 meter antennas: 6 meter antennas