6m 6elements Portable Yagi Antenna 6m6DX6A for DXing and Expeditions
This 6m 6elements Portable Yagi Antenna 6m6DX6A has adjusted parts lengths to fit airplane “Checked baggage” size 120cm or 47″ or to fit almost any trunk of the vehicle. Take this antenna to portable locations and enjoy ultimate DX with this superb antenna. To assemble in portable you will need no more than 15 minutes.
6m 6elements Portable Yagi Antenna 6m6DX6A
What does 6m6DX6A mean?
- 6m – 6m portable Yagi antenna
- 6 – 6 elements
- DX – Intended for use in DX part of band 50-50.5MHz with excellent SWR
- 6 – Almost 6m boom length
- A – Boom or element parts length up to 118cm or 47″ (for ANY transport)
Electrical Specifications of 6m 6elements Portable Yagi Antenna 6m6DX6A
Frequency Range: 50 – 50.5 MHz
Free Space Forward Gain: 11.45 dBi
Front-to-Back Ratio: 31 dB
-3 dB Horizontal Beamwidth: 47.1°
Nominal Input Impedance: 50 Ohms
SWR Across Entire Band: <1.2
Maximum Power Input: 1000 W
Matching Method: Direct feed through common mode choke (current balun)
6m 6elements Portable Yagi Antenna 6m6DX6A Azimuth Radiation Pattern
Mechanical specifications of 6m 6elements Portable Yagi Antenna 6m6DX6A
Number of Elements: 6
Elements Diameter: Tapered elements. Center tube 12mm, extensions 10 and 8mm
Dipole Diameter: Tapered dipole. Center tube 12mm, extensions 10 and 8mm
Longest Element: 3.1 meter
Element Mounting Position: Below the boom
Balun and Connector: Included
Boom Length: 5.74 meter
Boom Size: Tapered boom. 40 x 40 mm, 30 x 30 mm, 20 x 20 mm
Turning Radius: 3.2 meter
Number of Boom Pieces: 5
Guy rope support: Yes, Included*
Mounting Mast Diameter: 43 – 70 mm 1-11/16″ – 2-3/4″ OD
Clamp: 2 x M8 Stainless Steel
Survival Wind Speed: 150 km/h
Wind Load: 0.27 m2
Net Weight: 7.7 kg
Gross Weight: 9.2 kg
Transportation Length: 1.2 m
* Guy rope support is not necessary for one-two days of use.
Antennas-Amplifiers Product Benefits. A Major advance in Amateur Radio antenna design.
- F/B and G/T superiority.
All antennas have been calculated using state-of-the-art full 3D Electromagnetic Simulation Software including the influence of the boom, bracket, baluns, and connectors. The performance of antennas designed using these techniques is exceptional, far better than antennas designed using “wire” programs.
Comparison of EM simulation software
- No tuning antennas
Before dispatch, we assemble each antenna and test antenna characteristics. That means you may expect exceptionally good electrical and mechanical attributes including low SWR across the designed range immediately after assembling.
No need to tune the dipole, or any other element to get perfect SWR on the intended frequency range. Everything is pre-tuned.
- Easy to set up
Everything is labeled, just put number to number. The antenna can be assembled with hand tools in a couple of minutes.
Everything is included in the antenna box: Antenna, balun with connector, and bracket. Yours is to assemble and have fun!
The old name of the antenna was PA50-6-6AG
Check all 6m antennas here
There are no reviews yet.